CCNAv7 SRWE: Network Config.

CCNAv7 SRWE Practical: Configure Network Infrastructure Settings

CCNAv7 SRWE Practical

CCNAv7 SRWE Practical: Part I: Configure Network Infrastructure Settings (VLANs, Trunking, Etherchannel) Part II: Configure DHCP and Switchport Security Part III: Test and Verify IPv4 and IPv6 End-to-End Connectivity

Assessment Objectives

Part I: Configure Network Infrastructure Settings (VLANs, Trunking, Etherchannel)

Part II: Configure DHCP and Switchport Security

Part III: Test and Verify IPv4 and IPv6 End-to-End Connectivity

In this Skills Assessment (SA) you will configure the devices in a small network. You must configure a router, switch and PCs to support both IPv4 and IPv6 connectivity for supported hosts. Your router and switch must also be managed securely. You will configure inter-VLAN routing, DHCP, Etherchannel, and port-security.

1 Router (Cisco 4221)
2 Switches (Cisco 2960)
2 PCs
Console cables to configure the Cisco IOS devices via the console ports
Ethernet cables as shown in the topology

Part 1: Configure Network Infrastructure Settings (VLANs, Trunking, Etherchannel)

Step 1: Create a new .pkt file in PacketTracer. Create the topology above using the correct cabling. NOTE: console cables are not required for this activity.

Step 2: Configure S1 and S2:

Task	Specification
Disable DNS lookup
Switch name	S1 or S2, as appropriate
Domain name	ccna-lab.com
Encrypted privileged EXEC password	Cisco2practical
Console access password	Cisco2practical
Encrypt the clear text passwords
Configure an MOTD Banner
Configure Management Interface (SVI)	Set the Layer 3 IPv4 address Set the Ipv6 Link Local Address as FE80::98 for S1 and FE80::99 for S2 Set the Layer 3 IPv6 address
Configure Default Gateway	Configure the default gateway as 10.19.8.97 for IPv4

Step 3: Configure R1.

Configuration tasks for R1 include the following:

Task	Specification
Disable DNS lookup
Router name	R1
Domain name	ccna-lab.com
Encrypted privileged EXEC password	Cisco2practical
Console access password	Cisco2practical
Encrypt the clear text passwords
Configure an MOTD Banner

Step 4: Configure S1.

Configuration tasks for S1 include the following:

Task	Specification
Create VLANs	VLAN 2, name Bikes VLAN 3, name Trikes VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native
Create 802.1Q trunks that use the native VLAN 6	Interfaces F0/1, F0/2, and F0/5
Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2	Use the LACP protocol for negotiation
Configure host access port for VLAN 2	Interface F0/6
Configure port-security on access ports	Allow 3 MAC addresses
Secure all unused interfaces	Assign to VLAN 5, Set to access mode, add a description, and shutdown

Step 5: Configure S2.

Configuration tasks for S2 include the following:

Task	Specification
Create VLANs	VLAN 2, name Bikes VLAN 3, name Trikes VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native
Create 802.1Q trunks that use the native VLAN 6	Interfaces F0/1 and F0/2
Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2	Use the LACP protocol for negotiation
Configure host access port for VLAN 3	Interface F0/18
Configure port-security on access ports	Allow 3 MAC addresses
Secure all unused interfaces	Assign to VLAN 5, Set to access mode, add a description, and shutdown

Step 6: Document Your Work

Create a new document (.doc or .docx) and document your work. You are welcome to do this in any manner you wish. However, it must include all information needed for someone to re-create your work without any prior knowledge.

Get instant help from 5000+ experts for